Hussman 0425683F User Manual

®P/N 0425683FSeptember 2006INNOVATORANDINNOVATOR IIREACH-INGLASS DOORINSTALLATION& SERVICEMANUAL

As shown in Figure 15, this can also be accom-plished by pushing the magnet across the gap fromthe outside with a pencil or other non-heat conduct-ing

FRAME HEATER REPLACEMENTAlways turn off power to the case before workingon any electrical components. The old wirewaycovers must be removed to access

During installation, the white portion of theheater should not come in contact with itself. Theheater should be installed so that only one whiteportio

LAMP (CENTER MULLION)REPLACEMENTNote: No additional parts need to be removed tochange out the lamps1. Turn off lights at switch.2. Disengage the diff

shelf and over the lamp tube and wires. The toppart of the diffuser must be below the honeycombretainer and above the lamp tube. The bottomfiller need

LAMP (END MULLION ) REPLACEMENT1. Turn off lights at switch. 2. Pry the diffuser away from the end reflector,using a flat blade screwdriver. Pull the

P/N 0425683F®14HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COMFrame HeaterDoor Heater HarnessTerminal BlockTypical Low Tem

Innovator Door Installation andService InstructionP/N 0425683F15HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COMF58 T8 Lamp

P/N 0425683F®16HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COMF58 T8 LampF58 T8 LampF58 T8 LampF58 T8 LampF58 T8 LampF58 T

Harness, Female Receptacle (not used with medium temperature or Innovator II)Screw, Case End ShoulderWasher, Flat Torsion AssemblyCloser, DoorRetaine

IMPORTANTKEEP IN STORE FOR FUTURE REFERENCEQuality that sets industry standards!12999 St. Charles Rock Road • Bridgeton, MO 63044-2483 U.S. & Cana

Ballast–One Lamp 1/F58/120v 0430329 BA.4480341 4480341Ballast–Two Lamp 2/F58/120v 0430330 BA.4480342 4480342Ballast–Three Lamp 3/F58/120V 0454319 B

Cover–Wireway 5 Door Center Black 0428572 TP.0428572 4910114Cover–Wireway 5 Door Center Gray 0428581 TP.0428581 4910122Cover–Wireway 5 Door Center 311

Door–Innovator Low Temp Black Lh — RLT 0456167 DO.4981150 4981150Door–Innovator Low Temp Black Rh — RLT 0445379 DO.4980999 4980999Door–Innovator Lo

Gasket–Black Magnetic — Standard 0428562 GA.4330101 4330101Gasket–Gray Magnetic — Standard 0428563 GA.4330102 4330102Gasket–Black Magnetic — RLT 0461

P/N 0425683F22HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. • WWW.HUSSMANN.COMHeater–Frame Wire 2 Door Innovator II & Med Temp 0440150

Retainer–Door Black 0458446 TP.4913201 4913201Retainer–Door Silver 0458447 TP.4978039 4978039Screw–Handle 0428558 XX.0428558 4550108Screw–Harness 0428

APPENDIX A –REPLACEMENT BALLASTWIRINGThe diagrams below may be ofassistance when changing fromone ballast type to another. All wiring must be done in

®To obtain warranty information or other support, contact your Hussmann representative.Please include the model and serial number of the product.Hussm

GENERALBe sure merchandisers have been leveled accord-ing to the installation instructions shipped withthe merchandiser. The door nameplate is attache

ADJUSTING DOOR SAGTo adjust door sag (saw-tooth effect from door todoor), loosen the two hinge plate mountingscrews using a Torx Plus no. 27 bit. Adju

REPLACING DOORS1. Loosen torque on door before removing thedoor. Wedge a screwdriver between the bottom ofthe door and the hinge socket, then lift the

2. Unscrew the two #6 Phillips screws that holdthe black plug into the side of the door as shownin Figure 4. Remove the plug from the door. 3. Grasp t

6. Rock the door out and pull the bottom hingepin out from the bottom socket.7. Install the new door in reverse order.8. Adjust the torque on the new

Work from the corners to the centers of each side,top and bottom. Carefully push the new gasketinto the groove at each corner, refer to Figure10(A). T

Heat the GasketMake sure the door is closed.Beginning at the top of the gap,use a heat gun or electric hairdryer (1500-1600 watt) to heatthe gasket wi